Brother FAX 560 Service Manual Download Page 151

Page: 151 / 194

- 18

[ 5 ] Print-image related

If the received or sent image has any problem, first make a copy with the facsimile equipment.

If the copied image is normal, the problem may be due to the remote terminal; if it is abnormal,

proceed to the following checks:

Trouble

Check:

(1) Completely blank

At the scanner

At the recorder

• Main PCB
• CIS unit
• CIS-main harness

• Main-head harness and head-power harness
• Compression springs beneath the recording head
• Recording head
• Main PCB

(2) White vertical streaks

At the scanner

At the recorder

• CIS unit

• Recording head

(3) All black

At the scanner

At the recorder

• CIS-main harness
• CIS unit
• Main PCB

• Main-head harness and head-power harness
• Recording head
• Main PCB

(4) Black vertical streaks

At the scanner

At the recorder

• CIS unit

• Recording head

(5) Light or dark

At the scanner

At the recorder

• CIS unit
• Main PCB

• Compression springs beneath the recording head
• Position of the head adjuster

(6) Faulty image registration

At the scanner

At the recorder

• CIS-main harness
• CIS unit
• Main PCB

• Main-head harness and head-power harness
• Main PCB
• Recording head

Summary of Contents for FAX 560



































































































































































































Search results

Summary of Contents for FAX 560

Reviews:

Related manuals for FAX 560

Brands by name

Popular brands

Brother FAX 560, Service Manual

Search results

Summary of Contents for FAX 560

Reviews:

Related manuals for FAX 560

Brands by name

Popular brands