Brother FAX 560 Service Manual Download Page 143

Page: 143 / 194

- 10

(3)

Compatibility [checking the NSF and DIS]

Code 1

Code 2

Causes

Remote terminal only with V.29 capability in 2400 or 4800 bps

transmission.

Remote terminal not ready for polling.

Remote terminal not equipped with password function or its

password switch OFF.

Remote terminal not equipped with or not ready for confidential

mail box function.

Remote terminal not equipped with or not ready for relay

broadcasting function.

No confidential mail in the remote terminal.

The available memory space of the remote terminal is less than

that required for reception of the confidential or relay broadcasting

instruction.

Summary of Contents for FAX 560



































































































































































































Search results

Summary of Contents for FAX 560

Reviews:

Related manuals for FAX 560

Brands by name

Popular brands

Brother FAX 560, Service Manual

Search results

Summary of Contents for FAX 560

Reviews:

Related manuals for FAX 560

Brands by name

Popular brands