Brother BAS-761 Instruction Manual Download Page 95

Page: 95 / 155

Programmer

Chapter 3 Programming with Command Function

Move the needle with

. Press

when the needle point is at 5'.

5' is programmed.

Repeat step 1 and program 6' and 7'.

Press

, then press

The needle point moves to 5.

Deleting unnecessary points

Press

Input the number of stitches to be deleted, then

press

The example is deleting 3 stitches ahead. Press

The needle point moves to 6, 7 and 8. Points 5,

6 and 7 are deleted.

Saving

Specify the program number on the operation

panel, then press

switch for writing into the

floppy disk.

Refer to "Using the operation panel of the main body"(page 131)
for detailed operation.

Ending program

Press

Summary of Contents for BAS-761




























































































































































Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands

Brother BAS-761, Instruction Manual

Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands