Brother BAS-761 Instruction Manual Download Page 112

Page: 112 / 155

Programmer

111

Chapter 3 Programming with Command Function

Checking the program setting and

setting attribute

Checking the program setting and setting attribute

The following items are displayed.

Current coordinate

Distance from the previous position in the X and Y axial directions

Stitch length

End code

Current needle position / Total stitch count

Stitch data type

is displayed.

Needle tacking (*)

Needle tacking is set for each stitch.

Two step tension setting (*)

Two step tension output is set in the current needle position.

Two row switch (*)

The clamp is set inside when it is set to ON and is set

outside when it is changed from ON to OFF.

Option output (*)

Whether option output is conducted or not is set.

Slow conversion (*)

Three successive stitches at low speed are set. Values 500

to 33500 rpm are available for the speed.

Feed data type

is displayed.

Option output (*)

Whether option output is conducted or not is set.

The cylinder operates when chancing option output, two row switch, and two step tension

setting.

The option output is connected to the following ports

Number of connector

P26(MN-OPT-OUT)

Number of common pin

5 or 6 (+24V)

Number of signal pin

Two row switch can be set only in one position in one program. The newly set point be-

comes valid if two row switch is already set in the program.

Attribute of items marked with * are available for setting.

An example of stitch data is shown below.

Current stitch count

Distance from the previous point in
the direction of X or Y axis

End code

Slow conversion (*)

Two row switch (*)

Option output (*)

Two step tension setting (*)

Total stitch count

Current stitch count

Stitch data type

Needle tacking (*)

Stitch length

Summary of Contents for BAS-761




























































































































































Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands

Brother BAS-761, Instruction Manual

Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands