Brother BAS-761 Instruction Manual Download Page 85

Page: 85 / 155

Programmer

Chapter 3 Programming with Command Function

Programming example

Frequently used programming method is explained here. Refer to "Programming" (page 105) for function

and operation of each icon.

Programming for each stitch

Program each stitch according to the pattern. The
example in the left is used for explanation.

Programming

Press

The work clamp comes down and the programmer screen is
displayed.

Move the needle with

. Press

when the needle point is at point A of the

pattern.

The first stitch (point A) is programmed.

Repeat step 2 and create the program to

point C.

Inputting the end code

Press

at the last stitch and press

The needle returns to the sewing start position.

Saving

Specify the program number on the operation

panel, then press

switch for writing into

the floppy disk.

Refer to "Using the operation panel of the main body" (page
129) for detailed operation.

Summary of Contents for BAS-761




























































































































































Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands

Brother BAS-761, Instruction Manual

Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands