Brother BAS-761 Instruction Manual Download Page 152

Page: 152 / 155

151

Chapter 5 Practical programming examples

Programmer

Operating procedure

Programming

1. Press

The work clamp comes down and the programmer screen is displayed.

2. Move the needle with

. Press

when

the needle point is at point A of the pattern.

The first stitch (point A) is programmed.

3. Input the stitch length.

3.0 mm is input in the example.

4. Press

To change the stitch length, specify it before pressing

5. Move the needle with

. Press

when

the needle point is at point B of the pattern.

6. Press

7. Move the needle with

. Press

when

the needle point is at point C of the pattern.

8. Repeat step 7 and create the program to point F.

9. Move the needle with

. Press

when the needle point is at point

G of the pattern.

Point E is programmed to be a corner.

10. Press

11. Repeat steps 7, 8, and 9 and create the program

to point L.

Summary of Contents for BAS-761




























































































































































Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands

Brother BAS-761, Instruction Manual

Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands