Brother BAS-761 Instruction Manual Download Page 35

Page: 35 / 155

Programmer

Chapter 2 Programming with Help Function

Needle racking

Needle tacking is programmed.

Tacking width is set with the dial on the back of the top part of

the machine while needle tacking length is set with the pro-

grammer. Values 1.0 to 3.5 mm are available for the tacking

width.

Values 0.1 to 1.0 mm are available for the stitch length.

The needle actually drops at the point B' because needle tacking is conducted on the machine side. However, point

B of the program is created on the straight line between point A and point C.

Programming

Create the program to point A.

Select

with

, then press

Input the stitch length, then press

0.5 mm is input in the example.

Input 050 to make the width and the stitch length to 0.5 mm.

Move the needle with

. Press

when the needle point is at point B of the

pattern.

Press

ESC

twice.

Continue programming.

Zigzag

width

Stitch length

Summary of Contents for BAS-761




























































































































































Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands

Brother BAS-761, Instruction Manual

Search results

Summary of Contents for BAS-761

Reviews:

Related manuals for BAS-761

Brands by name

Popular brands