manualshive.com logo in svg

Brocade Communications Systems FCX 648S, Step-By-Step Manual

Share
Download
Brocade Communications Systems FCX 648S Step-By-Step Manual Download Page 23

DATA CENTER 

 

CONFIGURATION GUIDE 

 

 

 

Configuring an iSCSI SAN Using Brocade FCX Switches 

 

23 

 

! 
interface ethernet 1/1/22 
 flow-control neg-on 
! 
interface ethernet 1/1/23 
 flow-control neg-on 
! 
interface ethernet 1/2/3 
 link-aggregate active                                             
! 
interface ethernet 1/2/4 
 link-aggregate active 
! 
interface ethernet 2/1/5 
 flow-control neg-on 
! 
interface ethernet 2/1/6 
 flow-control neg-on 
! 
interface ethernet 2/1/15 
 flow-control neg-on 
! 
interface ethernet 2/1/16 
 flow-control neg-on 
! 
interface ethernet 2/2/3 
 link-aggregate active 
! 
interface ethernet 2/2/4 
 link-aggregate active 
! 
!                                                                  
! 
! 
! 
! 
! 
end 
 
telnet@STACK1(config)# 
telnet@STACK2(config)#show running-config  
Current configuration: 
! 
ver 07.1.00T7f1 
! 
stack unit 1 
  module 1 fcx-48-4x-port-management-module 
  module 2 fcx-sfp-plus-4-port-10g-module 
  stack-port 1/2/1 1/2/2 
stack unit 2 
  module 1 fcx-48-4x-port-management-module 
  module 2 fcx-sfp-plus-4-port-10g-module 
  stack-port 2/2/1 2/2/2 
stack enable 
! 
! 
! 
! 
! 
spanning-tree 802-1w 
! 
! 
buffer-sharing-full 

Summary of Contents for FCX 648S

























Reviews:

No comments

Brands by name

Popular brands

Load more brands