manualshive.com logo in svg

Brocade Communications Systems 6542, Hardware Reference Manual

Share
Download
Brocade Communications Systems 6542 Hardware Reference Manual Download Page 23

Brocade 6542 Blade Server SAN I/O Module for Inspur Shangri-la Chassis Hardware Reference Manual
53-1003885-01

 

23

Electrical considerations 

 

 

 

 
 

 

 

•  Take additional care when you handle devices during cold weather. Heating reduces indoor 

humidity and increases static electricity. 

•  The chassis comes with electrostatic discharge (ESD) connectors. Refer to the documentation that 

comes with the chassis for using the ESD connector. 

 

 

Electrical considerations 

 

The Brocade 6542 16-Gbps FC Switch Module requires a maximum of 140 watts, which is provided by 
a 12 V power supply from the Inspur Shangri-la Blade Server chassis. Out of this 12 V power input, 
3.3 V is provided by a standby power supply. No other power requirement or provision exists. 

 

 

Environmental considerations 

 

Ensure proper cooling and ventilation by verifying the following: 

 

•  Air vents on the blade server are not blocked or restricted. 
•  Ambient air temperature at the front of the enclosure does not exceed 35ºC (95ºF) while the 

switch module is operating. 

 

 

 

Preparing the blade server for the switch module 

 

 

Before the Brocade 6542 16-Gbps FC Switch Module can be inserted in the Inspur Shangri-la Blade 
Server chassis, make sure the following conditions are met: 

 

•  The blade server is powered up. 
•  The I/O module bay into which the Brocade 6542 16-Gbps FC Switch Module will be inserted is 

empty and ready to receive the switch module. 

•  All power requirements specific to the Inspur Shangri-la Blade Server chassis are met. 
•  If you are replacing an existing switch module with a new one, the new one should be ready to be 

inserted within one minute from removal of the old one to maintain the proper cooling level in the 
chassis. 

 

 

 

Inserting the switch module in the chassis 

 

 

Insert the switch module in the blade server chassis in the required slot and check for proper 
functioning of the switch modules. 

 

Perform the following procedure to insert the switch module in the blade server chassis. 

 

 

 

NOTE

 

The switch module is designed to work in specific switch module slots in the blade server chassis. Do 
not insert the switch module in any other slot because it will not work. 

 

1. Verify that the blade server chassis switch module slot into which the switch module is being inserted 

is empty. Switch module slots are marked in the following figure. 

Summary of Contents for 6542





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands