manualshive.com logo in svg

Brink Air 70, Installation Instructions Manual, Page: 7 / 40

Share
Download
Brink Air 70 Installation Instructions Manual Download Page 7

 

Air 70   Rev. D 

3

The Brink Air 70 is a decentral heat recovery ventilation unit for 
application in an exterior wall. The maximum ventilation capac-
ity of the appliance is 70 m

3

/h.

Features Air 70:

‡ DLUTXDQWLW\DGMXVWDEOHXVLQJFRQWUROEXWWRQV
‡ ¿OWHULQGLFDWLRQRQWKHDSSOLDQFH
‡ DIURVWSURWHFWLRQV\VWHPWKDWDOVRDWORZRXWGRRUWHPSHUD

-

tures ensures that the appliance's performance remains op-
timal and, if necessary, activates the standard preheater

‡ ORZVRXQGOHYHO
‡ FRPHVDVVWDQGDUGZLWKDXWRPDWLFE\SDVVYDOYH
‡ ORZHQHUJ\FRQVXPSWLRQ
‡ KLJKHI¿FLHQF\

The performance and the energy consumption of the Air 70 

GHSHQGRQWKHDLUTXDQWLW\VHWWLQJDVZHOODVRQWKH¿OWHUIRXOLQJ

The Air 70 is available in two types:

‡ ³$LU´
‡ ³$LU´

Compared to the standard Air 70, the Air 70 Plus has a more 
advanced control pcb with additional connection options for, 
among others, RH (humidity) sensor, CO

2

-sensor, multiple 

switch or Brink Home i module.
These installation instructions describe both the standard Air 
70 and the Air 70 Plus.
Please state the correct type when ordering an appliance.
For dimensions, see §3.2.

The Air 70 comes ready to plug in with a 230 V mains plug and 
a connection for the Brink service tool on the outside of the 
appliance.

The appliance comes with an emergency cap. In the event of 
an emergency for which the air supply and exhaust to the at-
mosphere must be shut off, the emergency cap must be placed. 

7KLVFDSLVVWRUHGLQWKHDSSOLDQFH%HIRUHSODFLQJWKHFDS¿UVW

the appliance must be switched off (pull the mains plug or, if 
installed, put the On/Off switch to 0).
See §11.1 for more detailed information.

Always remove this calamity cap before switching the 

appliance back on! 

Chapter 2    Application

  

Warning 

 

      The preheater and the Control pcb carry 230 V. Always take the voltage from the appliance 

by pulling the mains plug when working on the appliance.

Summary of Contents for Air 70









































Reviews:

No comments