BRAYER BR1102, Instruction Manual

Page: 8 / 39

14 15 EN EN
• Switch the coffee maker on by setting the power switch
(11) «0/I» to the position «I», the indicator (6) will light
up and start flashing.
• When the coffee maker is ready for operation, the light
indicator (6) will glow constantly.
• To make one cup of latte use a small filter (19) and
press the «Latte»-button (8) once; the light indicator «
» will light up.
• To make two cups of latte use a big filter (20) and press
the «Latte»-button (8) twice; the light indicator «
»
will light up.
Note: if you need to switch the coffee maker off during the
latte making, press the «Latte»-button (8) again.
• Remove the cup with the ready drink from the grid (2).
• After you finish using the coffee maker, switch the
coffee maker off by setting the switch (11) «0/I» to the
position «0».
• Wait until the coffee maker cools down, remove the
filter holder (18) and wash the filter (19 or 20).
• If there is some milk left in the cappuccinator, remove it
and put the cappuccinator into the fridge (pic. 10), if you
used all milk during making coffee, it is recommended
to remove the cappuccinator and clean it (see the
chapter «CAPPUCCINATOR CLEANING»).
MAKING FROTHED MILK
• You can make necessary amount of frothed milk
anytime.
• You can use the frothed milk for making hot chocolate,
macchiato, masala tea etc.
• It is important that milk for making frothed milk is fresh and
cold and without additives.
• Take usual whole milk with fat status from 4% to 6%,
cream fat status is not less than 10%.
• Prepare the coffee maker as described in the chapters
above, but do not add ground coffee into the filters (19 or
20).
• Place a cup of suitable height and capacity on the grid (2).
• Direct the cappuccinator pipe (13) into the cup using the
cappuccinator pipe angle adjustment bar (12).
• Turn the frothed milk supply (intensity) control knob (15)
to the right (in this position it produces more frothed milk)
(pic. 8).
• Switch the coffee maker on by setting the power switch
(11) «0/I» to the position «I», the indicator (6) will light up
and start flashing.
• When the coffee maker is ready for operation, the light
indicator (6) will glow constantly.
• Press and hold the «Cappuccino»-button (7) for 3
seconds, the indicators « » and « » will light up.
• After making the necessary amount of frothed milk stop
the process by pressing the «Cappuccino»-button (7)
again.
• Remove the cup with frothed milk and use the frothed milk
for the intended purpose.
• After you finish using the coffee maker, switch the coffee
maker off by setting the switch (11) «0/I» to the position
«0».
• If there is some milk left in the cappuccinator, remove it
and put the cappuccinator into the fridge (pic. 10), if you
used all milk during making coffee, it is recommended
to remove the cappuccinator and clean it (see the
chapter «CAPPUCCINATOR CLEANING»).
CAPPUCCINATOR CLEANING
• We recommend cleaning the cappuccinator after the
milk container (16) is empty.
• Take the container (16) and remove it (pic. 1), remove
the cappuccinator lid (14) from the container (16).
• Wash the container (16) with a neutral detergent,
remove the milk intake pipe from the cappuccinator lid
(14) and wash it, rinse all the parts, dry them and install
the milk intake pipe back to its place.
• Turn the steam nozzle counterclockwise to the position
« » and remove it from the cappuccinator (14) body
(pic. 11), wash the nozzle.
• Set the cappuccinator pipe angle adjustment bar (12) in
vertical position, take the bar (12) and slightly sway, pull
the cappuccinator pipe (13) towards yourself, remove
the cappuccinator pipe (13) and wash it.
• Grasp the left side and raise the silicone plug, rinse the
cappuccinator lid (14) under a warm water jet (pic. 12),
close the silicone plug.
• Install the cappuccinator pipe (13) back to its place,
install the steam nozzle back to its place and turn it
clockwise to the position « » (pic. 13).
• Prepare the coffee maker as described in the chapters
above, but do not add ground coffee into the filter (19
or 20).
• Place a cup of suitable height and capacity on the grid
(2).
• Fill the container (16) with water, do not exceed the
maximal level mark.
• Install the cappuccinator lid (14) on the container (16)
and install the cappuccinator back to its place until the
lock clicking.
• Direct the cappuccinator pipe (13) into the cup using the
cappuccinator pipe angle adjustment bar (12).
• Turn the frothed milk supply (intensity) control knob (15)
to the right to the position « ».
• Switch the coffee maker on by setting the power switch
(11) «0/I» to the position «I», the indicator (6) will light up
and start flashing.
• When the coffee maker is ready for operation, the light
indicator (6) will glow constantly.
• Press and hold the «Latte»-button (5) for 3 seconds, the
indicators « « and « « will light up.
• After you finish using the coffee maker, switch the coffee
maker off by setting the switch (11) «0/I» to the position
«0».
• Wait until the coffee maker cools down, take the
container (16), pull it towards yourself and remove it (pic.
1), remove the cappuccinator lid (14) from the container
(16).
• Pour the remaining water out of the container (16), wipe
the container with a dry cloth and dry the cappuccinator
lid (14).