background image

2

Phenolic Privacy Restroom Partitions, Floor-to-Ceiling — Series 700, — 69", 72" & 69"/72" Tall

 Installation

6/25/2021 

Bradley • 

HDWC-INSTR-045 Rev. A: ECO 20-14-002S

Safety Information

Warning

Before beginning installation, make sure that the wall and floor backing are adequate to support the secure mounting of the toilet 
compartment units .
Partitions are extremely heavy and may require more than one person to position and install .
Failure to comply with these instructions may result in personal injury and/or property damage and will void the partition warranty .

Caution

Personal protective equipment (PPE) is required during the installation and maintenance of this product .

Notice

To prevent warping, always lay the material flat . Do not lean the material against the wall or stack unevenly .
Make sure all floors and walls are clean and smooth . Remove loose impediments, such as protruding nails and other debris which 
could affect installation . 
To minimize break-out, always use a support block when drilling through the material .
Carefully remove components from skid, do not drag .

Important

Review your partition layout drawings and verify the number of stalls and components before beginning installation . All 
components are labeled with their corresponding part number . Descriptions and part numbers for doors, pilasters, and pilaster 
configurations are listed on pages 4–8 for easy identification .
Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department . 
This installation manual provides instruction for the assembly of normal partition configurations and standard components . 
Non-standard configurations or components including but not limited to curved or angled walls, partial walls, oversized panels, or 
modified hardware are not covered in this manual . Compliance and conformity to local codes and ordinances is the responsibility  
of the installer . 

Separate parts from packaging and make sure all parts are accounted for before discarding packaging material . If any parts are 
missing, do not begin installation until you obtain the missing parts . 

Summary of Contents for Bradmar 700 Series


































Reviews: