manualshive.com logo in svg

Bosch MSI 60, Manual

Share
Download
Bosch MSI 60 Manual Download Page 84

11 | Online Measurement

84 / 120

Modular Sensor Interface MSI 60

Bosch Motorsport

11 Online Measurement

MSI 60

 configuration

– System configuration (channel configuration, CAN I/O, PWM Out, etc.) is stored in the

MSI 60.

– Use RaceCon to create and download configuration from the PC to MSI 60

– Communication interface: Ethernet

– Communication protocol: XCP

Online measurement and calibration

– System status and diagnosis

– Check and calibrate sensors in the vehicle.

– Live display of sensor values on the PC

– Use RaceCon for diagnosis, online measurement and calibration.

– Communication interface: Ethernet

– Communication protocol: XCP

11.1 Achieving an online Connection

This chapter describes how to set up the PC for access, going online and how to update

the firmware.

11.1.1 Set up the PC for Access

1.

Switch off local firewall on the PC.

2.

Set IP Configuration for the Ethernet interface to ‘automatic configuration’ (DHCP).

3.

Start RaceCon.

4.

Establish the Ethernet connection to the vehicle.

5.

Power on the vehicle.

6.

Click ‘OK’ to download RaceCon configuration to device.

Summary of Contents for MSI 60

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands