manualshive.com logo in svg

Bosch MSI 60, Manual

Share
Download
Bosch MSI 60 Manual Download Page 26

7 | Starting up

26 / 120

Modular Sensor Interface MSI 60

Bosch Motorsport

RaceCon detects configuration differences between the MSI 60 and the RaceCon pro-

ject and asks for permission for data download.

8.

Click ‘OK’ to proceed.

The download starts and the MSI 60 carries out a reset. After the reset RaceCon recon-

nects to the MSI 60 . Local configuration on both the PC and MSI 60 match (indicated by

green background and dot). The MSI 60 is now connected to RaceCon.

7.2 Assign the Mounting Location

Because up to eight MSI 60 can be used in one network for I/O expansion, the mounting

location is used for determination between the different MSI 60.

At delivery no mounting location is set. This is signaled by an orange ‘RUN’ LED on the

device. Therefore one must first assign a mounting location to the MSI 60 before it can be

used in the project. The mounting location is permanently saved in the MSI 60. If neces-

sary you can at any time reassign a different mounting location following the same pro-

cedure.

A mounting location must not be used several times in one network, this would disturb

the functionality of the respective MSI 60.

Summary of Contents for MSI 60

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands