manualshive.com logo in svg

Bosch MSI 60, Manual

Share
Download
Bosch MSI 60 Manual Download Page 113

GPS Sensor | 15

Bosch Motorsport

Modular Sensor Interface MSI 60

113 / 120

15.5 GPS Troubleshooting

Electrical

– Is the transmitter signal of the GPS sensor connected to the receiver pin of the serial

interface of the MSI 60?

– Is the GPS sensor powered up?

– Does the GPS sensor deliver RS232 signal levels?

Interface

– Do the baudrates of the GPS sensor and the device match?

– Is the GPS sensor set up for 8N1 transmission parameters?

– Is the GPS sensor set up for NMEA messages?

– Are the GGA, VTG, RMC messages activated?

– With a correctly wired and powered GPS sensor the changing GPS time information

(gps_sec) can be immediately observed.

GPS sensor start-up

– Does the GPS sensor ‘view’ the sky?

– Did the GPS sensor complete its initial start-up procedure? This may take up to 20

min.

– A correct reception is indicated when ‘gps_fix’ is showing ‘3D Fix’.

Summary of Contents for MSI 60

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands