manualshive.com logo in svg

Bosch MSI 60, Manual

Share
Download
Bosch MSI 60 Manual Download Page 72

10 | Analog and Frequency Inputs

72 / 120

Modular Sensor Interface MSI 60

Bosch Motorsport

The third part of the ‘Multipoint Adjustment Wizard’ opens.

a) Physical (channel) value.
b) Electrical (pin) value.
c) Enter physical limits of the sensor.
d) Choose data type of the measurement variable.
e) Enable additonal online calibration.
f) Enter name to automatically create a new measurement sheet.

3.

Click ‘Finish’ when done.

4.

Enter channel name and description.

5.

Click ‘OK’ when done.

The channel is inserted into the MSI 60 Project Tree.

a) Channel is linked to ANA06.
b) Available measurements for channel
c) Input pin pull-up resistor is activated.
d) Multipoint characteristic curve for sensor
e) Adjustment is enabled.

Available measurements for channel

Measurement label

Function

raw_name

mV value of sensor

raw_name_fi

filtered mV value of sensor

name

physical value of sensor

name_fi

filtered physical value

Summary of Contents for MSI 60

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands