Bosch MSI 60 Manual Download Page 5

Page: 5 / 120

Getting started | 1

Bosch Motorsport

Modular Sensor Interface MSI 60

5 / 120

1 Getting started

Use the MSI 60 only as intended in this manual. Any maintenance or repair must be per-

formed by authorized and qualified personnel approved by Bosch Motorsport.

Operation of the MSI 60 is only certified with the combinations and accessories that are

specified in this manual. The use of variant combinations, accessories and other devices

outside the scope of this manual are only permitted when they have been determined to

be compliant from a performance and safety standpoint by a representative from Bosch

Motorsport. Read the manual carefully and follow the application hints step by step. Don’t

hesitate to contact us, contact data can be found on the back page of this document.

Disclaimer

Due to continuous enhancements we reserve the rights to change any illustrations, photos

and technical data within this manual.

Summary of Contents for MSI 60

























































































































Search results

Summary of Contents for MSI 60

Reviews:

Brands by name

Popular brands

Bosch MSI 60, Manual

Search results

Summary of Contents for MSI 60

Reviews:

Brands by name

Popular brands