20
| English
1 609 92A 2DJ | (27.10.16)
Bosch Power Tools
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product are:
Sound pressure level 82 dB(A); Sound power level 93 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
h
(triax vector sum) and uncertainty K
determined according to EN 60745-2-3:
Surface grinding: a
h
=6.0 m/s
2
, K=1.5 m/s
2
,
Disk sanding: a
h
=2.5 m/s
2
, K=1.5 m/s
2
.
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
Battery Charging
Use only the battery chargers listed on the accessories
page.
Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note:
The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off.
The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery
The battery
5
is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button
6
unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery
5
, press the unlocking button
6
and
pull out the battery toward the front.
Do not exert any force.
Battery Charge-control Indication (see figure A)
The three green LEDs of the battery charge-control indicator
24
indicate the charge condition of the battery
5
. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button
23
to indicate the charge condition. This is also
possible when the battery
5
is removed.
When no LED lights up after pushing button
23
, then the bat-
tery is defective and must be replaced.
Thread length (max.) of grinder spindle
mm
22
22
Weight according to EPTA-Procedure 01:2014
kg
1.8/2.3*
1.8/2.3*
Permitted ambient temperature
– during charging
– during operation
**
and during storage
°C
°C
0...+45
–20...+50
0...+45
–20...+50
Recommended batteries
GBA 18V ...
GBA 18V ...
Recommended chargers
AL 18..
GAL3680
AL 18..
GAL3680
Angle Grinder
GWS 18 V-LI
GWS 18-125 V-LI
* depending on the battery pack being used
** Limited performance at temperatures <0 °C
LED
Capacity
Continuous lighting 3 x green
≥
2/3
Continuous lighting 2 x green
≥
1/3
Continuous lighting 1 x green
<1/3
Flashing light 1 x green
Reserve
OBJ_BUCH-1102-007.book Page 20 Thursday, October 27, 2016 2:35 PM
