Bosch FPA-1200-MPC Operation Manual Download Page 10

Page: 10 / 94

en | For your safety

Panel Controller

F.01U.076.969 | 6.0 | 2010.04

Operation guide

Bosch Sicherheitssysteme GmbH

For your safety

Before using the device, familiarize yourself with these instructions. If you do not read and

understand these explanations, you will not be able to operate the device faultlessly.

The operating instructions do not do away with the need for training by authorized personnel.

This operation guide does not contain any general or special knowledge about safety issues.

Information on such issues is only given to the extent that it is needed for operation of the

device.

Ensure that you are familiar with all safety-related processes and regulations in your area. This

also includes how to behave in the event of an alarm and the initial steps to take if a fire

breaks out.

The operation guide should always be available on site. It is a statutory part of the system and

must be given to the new owner if the system is ever sold.

2.1

Symbols and notes used

The various chapters only contain whatever safety information and notes are required for

operation of the system. Warning notes and operator guidance notes are displayed in the

appropriate parts of the panel controller display for your benefit.

The following search symbols are used:

2.2

Operating the touch screen

Do not use any pointed or sharp objects when operating the touch-sensitive display. This

could damage the surface. Touch the touch screen with your finger (nail) or the stick attached

to the left-hand side of the panel controller.

NOTICE!

The panel controller may only be operated by trained personnel. See skills required by

personnel.

NOTICE!

The personal access code (consisting of user ID and password) must not be made known to

third parties.

CAUTION!

Text fields marked with this symbol contain warnings by which you must abide without fail —

for your own safety as well as that of the people around you

NOTICE!

Text fields marked with this symbol contain useful information to help you operate the FPA-

5000 and FPA-1200 fire panels.

Summary of Contents for FPA-1200-MPC































































































Search results

Summary of Contents for FPA-1200-MPC

Reviews:

Related manuals for FPA-1200-MPC

Brands by name

Popular brands

Bosch FPA-1200-MPC, Operation Manual

Search results

Summary of Contents for FPA-1200-MPC

Reviews:

Related manuals for FPA-1200-MPC

Brands by name

Popular brands