Bosch DAS 3000 S20, Original Instructions Manual

Page: 17 / 20

1 689 989 485 | 2020-08-01 Robert Bosch GmbH
(3) Recess in spacer
(4) Spirit level
---
6. Maintenance
---Separator--- 6.1 Cleaning
Coarse workshop rags and abrasive cleaning
agents may damage the DAS 3000 S20 .

Use only neutral cleaning agents and soft cloths to
clean the DAS 3000 S20.
---Separator---
6.2 Spare parts
Denomination Order number
Rubber buffer (2x) on brake
<) 1 688 990 086
Star knob screws (2x) for attaching the "Multi-
Target-Shop" box
<)
1 686 621 080
Hammer nuts (2x) for the top camera's
mount
<)
3 842 530 283
Camera beam (without cameras) 1 682 391 559
Yellow protective caps (2x) for the camera
beam
1 683 212 042
Indicator bar with slide 1 682 329 109
Left slide (as viewed from the front) on the
indicator bar
<)
1 688 030 217
Right slide (as viewed from the front) on the
indicator bar
<)
1 688 030 215
Yellow protective caps (2x) for the indicator
bar
<)
1 683 212 041
End caps (2x) for the slide guide on the indi‐
cator bar
<)
1 683 212 040
Retaining cable
<)
1 684 712 028
Rubber magnets on the indicator bar 1 688 120 188
Spirit level on the indicator bar 1 687 233 114
Left positioning bar (as viewed from the
front)
1 688 040 326
Right positioning bar (as viewed from the
front)
1 688 040 323
Slider (2x) for the positioning bar
<) 3 842 552 424
Star handles (5x) suitable for vertical posi‐
tions A, B, C, D, radar position R, R position,
Z position
<)
1 686 621 078
Star handles (2x) suitable for securing the po‐
sitioning bar
<)
1 686 621 077
Star handle (1x) suitable for securing at the R
position and Z position
<)
1 686 621 081
T slot nut (2x) for the slider
<) 3 842 528 735
Left tape measure for the height of the indica‐
tor bar (as viewed from the front)
<)
1 687 233 119
Right tape measure for the height of the indi‐
cator bar (as viewed from the front)
<)
1 687 233 117
Cable carrier
<) 3 842 555 180
Calibration board CTA 300-1 for front camera
systems and front radar systems
1 681 098 011
Mounting adapter 1 (2x)
<) 1 685 720 380
Denomination Order number
Mounting adapter R (1x)
<) 1 685 720 384
Wheel holder CTA 100-1 1 688 120 190
Reference board CTA 400-1
<) 1 681 098 013
Wheel holder CTA 100-1 star handle 1 686 621 083
Wheel holder CTA 100-1 spacers (2x) 1 687 016 229
Wheel holder CTA 100-1 prongs (2x) 1 687 016 230
Wheel holder CTA 100-1 top bracket parts set 1 687 016 228
Reference board CTA 400-1 fastening parts
set
1 687 010 635
Contact plate CTA 104-1 1 681 320 090
Contact plate CTA 104-1 edge protection
<)
1 687 010 742
Left offset ruler (as viewed from the front) 1 688 132 049
Right offset ruler (as viewed from the front) 1 688 132 050
Rubber grommets (4x) for the parked position
of wheel holder CTA 400-x
<)
1 680 212 064
Rubber buffers (2x) for the parked position of
wheel holder CTA 400-x
<)
1 688 990 087
---
<)
Wearing parts
---
6.3 Replacing the positioning bar
1. Remove the front cover
(1)
on the frame.
4712005-44_shd
1
(1) Front cover
2. Loosen the knurled screws
(3)
for adjusting the
height of the positioning unit
(2)
.
3. Push the positioning unit
(2)
up and out of the edge
protection frame.
DAS 3000 S20 | 33 | en