EN
© 2005 Bosch Security Systems
Page 26 of 40
SECTION 12
AUTODOME LOCKED COMMANDS
Access to the AutoDome may be password-protected. See SECTION 4, AutoDome Security for details. To use Locked Commands, first unlock
the AutoDome via OFF-90-ENTER. All locked settings, except FastAddress, can then be changed via ON-46-ENTER. Disallow these commands via
ON-90-ENTER.
Section 12
Commands
Keystrokes
Description
FastAddress
On-999-Enter
Sets/changes the dome address using the keyboard and on-screen menus. (for cameras not already configured).
On-998-Enter
Sets/changes the dome address using the keyboard and on-screen menus. (for all cameras, even those already configured).
Display FastAddress
On-997-Enter
Briefly displays all dome addresses.
Auto Iris
On/Off-3-Enter
Camera (Iris) adjusts automatically/manually (On/Off) to light conditions.
Auto Focus
On/Off-4-Enter
Camera automatically/manually (On/Off) focuses.
Gain Control
On/Off-43-Enter
Turns gain control to Automatic or Off. When in Automatic mode, the gain increases to compensate for darker scenes.
On-screen Display
On/Off-60-Enter
Turns On/Off the On-screen Display. When off, there is no On-screen feedback.
On-screen
On/Off-61-Enter
Changes the characters and position of the display.
Display Adjust
On-screen instructions are provided.
Newer versions of the Receiver/Driver, in combination with firmware version 5.10 or higher, allow the brightness to be
adjusted. The firmware automatically detects whether the Receiver/Driver supports this, and displays the selection when
available.
Sector Title Edit
On/Off-63-Enter
Edits the current Sector name. On-screen instructions are provided.
Sector Blanking
On-86-Enter
Masks video from being displayed in selected sectors.
Privacy Masking
On-87-Enter
Masks video from being displayed in selected zones.
Bypass All
Off-86-Enter
Removes all viewing restrictions imposed by sector blanking/privacy masking but keeps their locations in memory.
Masks/Blanking
or Off-87-Enter
On-86/87-Enter reactivates all masks/blanking.
Lock/Unlock
On/Off-90-Enter
Allows/Disallows Locked Commands to be accessed.
Commands
Password
Set-802-Enter
Sets or displays password. See AutoDome Security, SECTION 4 for details.
Factory Home
Set-110-Enter
SET recalibrates camera and returns it to home position.
Position
Restore Defaults
On-40-Enter
Restores Factory Defaults.
Left Limit
Set-101-Enter
Sets the current position as the left limit of Auto Pan. Default is 0 degrees.
Right Limit
Set-102-Enter
Sets the current position as the right limit of Auto Pan. Default is 359.9 degrees.
Inactivity
On/Off-9-Enter
Selects the mode that the dome reverts to after a duration without operator activity. Default is OFF.
Preset
On/Off-15-Enter
Increase/Decrease (On/Off) the time between Presets during Preset Tour.
Tour Period
AutoPivot
On/Off-18-Enter
Allows a subject to be followed while beneath the camera, without inverting the picture. Default is ON.
AutoTrack Comms
On/Off-77-Enter
Enables/Disables the Tracker. When disabled, no status will be displayed. Since this is not retained in non-volatile memory, if
the AutoDome receives Tracker messages on start-up, the Tracker will be enabled again (AutoTracker option ONLY).
Camera Height
On/Off-79-Enter
Selects the height of the camera in respect to the surface being monitored with the AutoTracker feature
(AutoTracker option ONLY).
Select
On/Off-35-Enter
Adjusts camera color (white balance) for specific settings.
White Balance
or On/Off-30-Enter
Sharpness
On/Off-44-Enter
Picture (vertical aperture) sharpens/softens.
Iris Adjust
On/Off-11-Enter
Edits the Auto Iris level.
Shutter
On/Off-23-Enter
Sliding scale from 1 second to 1/10,000 sec,
(Frame Integration)
with Auto Slow Shutter at extreme left.
Sync Mode
On/Off-42-Enter
Sets camera sync for external-line/internal-crystal (On/Off).
Adjust Line
On/Off-41-Enter
Changes the phase delay of the camera when in
Lock Phase
external line lock mode.
Switch Polarity
On-91-Enter
Switches the polarity of the Zoom, Focus, and Iris controls.
Digital Zoom
On/Off-80-Enter
Enables (On) or disables (Off) the digital zoom.
Night Threshold Adj.
On-58-Enter
Selects the video level at which the camera switches to night mode (Day/Night only).
QuickSet Select
On-59-Enter
Allows mode selection where multiple camera settings are set according to the chart below (Day/Night only).
S
ETU
P
G
E
N
E
R
AL
PT
Z
CA
M
E
RA
QuickSet Mode Name
Gain Control
IRIS
Slow Shutter
IR Filter
Low Light Color
Auto
Auto
Auto
In
Full Auto w/ Slow Shutter
Auto
Auto
Auto
Auto
Full Auto w/o Slow Shutter
Auto
Auto
1/60
Auto
Night w/ Slow Shutter
Auto
Auto
Auto
Out
Night w/o Slow Shutter
Auto
Auto
1/60
Out
