manualshive.com logo in svg

BOMBARDIER Challenger 601-3A CL-600-2B16, Pilot Training Manual

The BOMBARDIER Challenger 601-3A CL-600-2B16 is a powerful and sophisticated private jet, renowned for its exceptional performance and luxurious amenities. To ensure you have all the necessary knowledge and skills to fly this aircraft, we provide a comprehensive Pilot Training Manual available for free download on our website manualshive.com.

Share
Download
background image

VENT SYSTEM

Each tank is vented at two different points
through a series of vent lines which allow air
to enter or escape the tanks, depending upon
whether fuel is being used or added (Figure 5-
11). The vent lines extend from each wingtip
to common manifolds which form an inter-
connected inverted “U” in each fuselage wall
and then return to the wing area where they ter-
minate under the trailing edge on each side in
a flush-mounted NACA scoop. The scoop,
which has ice rejection capability, maintains

a slight positive tank pressure during flight due
to ram-air effect.

There are no valves or screens in the vent
lines, so dirt or ice accumulation does not nor-
mally occur. Any trapped fuel or moisture in
the vent lines is continuously purged from the
low points by a bleed line connected to each
scavenge ejector.

During pressure fueling, the fuel tank vent lines
are augmented with special vent valves which will
be described later under “Pressure Refueling.”

FlightSafety Canada 

L t é e
L t d .

CL-600-2B16 PILOT TRAINING MANUAL

5-12

CL 601-3A

FOR TRAINING PURPOSES ONLY

AUXILIARY
TANK VENT

MAIN TANK

CLIMB VENT

MOTIVE

FLOW

PURGE
LINE

SCAVENGE FLOW
TO COLLECTOR TANK

MAIN TANK VENT

NACA SCOOP INLET

PURGE LINE

INVERTED U

VENT TUBE

SCAVENGE

EJECTOR

Figure 5-11.   Vent System

Summary of Contents for Challenger 601-3A CL-600-2B16




























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Challenger 601-3A CL-600-2B16

BGS technic 6685 Instruction Manual preview
6685
Brand: BGS technic Pages: 12
Ironton 45997 Owner'S Manual preview
45997
Brand: Ironton Pages: 21
Ancor 703023 Operator'S Manual preview
703023
Brand: Ancor Pages: 12
Maggi EVOLUTION 1000 User And Maintenance Manual preview
EVOLUTION 1000
Brand: Maggi Pages: 66
Bahco IZO-D User Manual preview
IZO-D
Brand: Bahco Pages: 52
Parkside PAT 12 A1 Translation Of The Original Instructions preview
PAT 12 A1
Brand: Parkside Pages: 65
Graco SDL23 Series Instructions Manual preview
SDL23 Series
Brand: Graco Pages: 54
BSM Dahle 250 Instructions Manual preview
Dahle 250
Brand: BSM Pages: 96
WAGNER Earlex WS125 Operating Manual preview
Earlex WS125
Brand: WAGNER Pages: 56
BorMann 028673 User Manual preview
028673
Brand: BorMann Pages: 9
CAMPAGNOLO CAMPY UT-CN200 Instruction Sheet preview
CAMPY UT-CN200
Brand: CAMPAGNOLO Pages: 2
Phoenix Contact 1212463 Operating Instructions Manual preview
1212463
Brand: Phoenix Contact Pages: 36
Ryobi P524 Manual preview
P524
Brand: Ryobi Pages: 2
MasterCraft 058-8191-0 Instruction Manual preview
058-8191-0
Brand: MasterCraft Pages: 28
Leigh R9PLUS User Manual preview
R9PLUS
Brand: Leigh Pages: 20
Central Forge 97160 Owner'S Manual & Safety Instructions preview
97160
Brand: Central Forge Pages: 4
TE Connectivity 90260-1 Instruction Sheet preview
90260-1
Brand: TE Connectivity Pages: 4
Max Re-Bar-Tier RB397 Operating And Maintenance Manual preview
Re-Bar-Tier RB397
Brand: Max Pages: 27

Brands by name

Popular brands

Load more brands