manualshive.com logo in svg

BOC Edwards Seiko Seiki STPH1303C, Instruction Manual

Share
Download
BOC Edwards Seiko Seiki STPH1303C Instruction Manual Download Page 97

STP-H803/H1303 Series Instruction Manual 

11.4 

"WARNING" Message Display Function 

The STP control unit is provided with a "WARNING" message to display when an 
overhaul is needed following a self test. 
When a "w" appears in the upper left hand corner of the LCD, press and hold the 
"ENTER" switch to display the warning message.    The warning message 
indicates that an overhaul is necessary.    Please contact Service office for an 
overhaul.    (The "ENTER" switch can also be used in Remote Mode.) 

 

Example: 

WARNING
First Damage Limit

    w            Levitation

"ENTER"

The upper line of the LCD displays the
operation status of the STP pump.    The "w"
is displayed in each state (acceleration,
normal operation, and deceleration) of the
pump.

Warning message

 

 

◇ 

The "WARNING" message cannot be reset by the "RESET" switch. 
Service office is in charge of resetting the "WARNING" message. 

◇ 

The STP pump can operate even when the "WARNING" message is 
displayed. 
It is recommended to have the STP pump overhauled as soon as 
possible. 

T

ro

ub

le

sh

oo

tin

g

 

◇ 

The STP pump can operate even when the "WARNING" message is 
displayed except when "Second Damage Limit" is displayed.   
Overhaul the STP pump when "Warning" message is displayed. 

 

11.4.1 

First Damage Limit 

The touch down bearing inside the STP pump will be worn out caused by impact 
or air in rush from outside.    Also, touch down at the power failure causes wear.   
The STP control unit adds the damage point at each "Disturbance" and "Mains 
Failure" error.    "First Damage Limit" is displayed when the accumulation point 
attains the prime setting value.    "First Damage Limit" cannot be reset.    It is 
recommended to have the STP pump overhauled as soon as possible. 

 

 

11-10

Summary of Contents for Seiko Seiki STPH1303C






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands