manualshive.com logo in svg

BOC Edwards Seiko Seiki STPH1303C, Instruction Manual

Share
Download
BOC Edwards Seiko Seiki STPH1303C Instruction Manual Download Page 19

STP-H803/H1303 Series Instruction Manual 

Installation

 

4)   STP Pump Installation Warning Label 

This label describes installation of the STP pump.     
Install the STP pump according to the precautions of Section 4, "Installation 
of the STP Pump." 

ポンプは取扱説明書の指示

に従い確実に固定してくだ
さい。

Install pump securely

according to instruction
manual. 

警告

!

WARNING

!

 

 

5)   STP Control Unit Safety Instruction Label 

This label describes instructions before operating the STP control unit. 

安全上の指示事項

SAFETY INSTRUCTIONS

使用前に取扱説明書を
お読みください。

Read instruction manual
before operation.

 

 

6)    Connector Caution Label 

◇ 

This label describes lock of the connector. 

◇ 

This label instructs operators to prevent the connectors from being 
disconnected while the STP pump is in operation. 

◇コネクタは確実に
  ロックしてくださ

  い。
◇ブレーカＯＮの時

  はコネクタを外さ

  ないでください。

◇Lock connector
  secureiy.

◇Do not remove

  connector while

  breaker is ON.

注意

!

CAUTION

!

 

 

 

1-3

Summary of Contents for Seiko Seiki STPH1303C






























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands