manualshive.com logo in svg

Blease 8500, Training Manual, Page: 40 / 69

Share
Download
Blease 8500 Training Manual Download Page 40

Title:  Final Test 8500 

Document No: 129TP000 

Sheet 13 of 17 

 

 

 

BLEASE QUALITY DOCUMENT 

BQD 083.V2 

25/5/94   

 

 

 

 

 

 

 

 

 

 

Checked:-________   

5.24  Dealer specific information 

The following options can be set: 

Absorber   

Present  (default) / Not present  

Language   

English (default), German, French, Spanish, Turkish, Italian 

O.E.M   

 

Blease (default), A.M.S, Acoma, Finesa, User select 

The Absorber switch setting can be found under setup enter the password “TECHY” 

The Language and O.E.M settings can also be found under setup enter the password “LINGO” 

If anything other than the default options are required then these should be set 

All options should be recorded on the calibration record even if they are default. 

5.25  Test Completion 

Restore ventilator controls to default. Ensure mode on/off switch is in the OFF.   

Check that all the noted readings are within the tolerances as specified in section 4. 

Sign off the 'Checklist and Calibration Record' and the customer printout. Ensure both have the 
ventilator serial number, date and signature of final tester, etc. 

 

 

If the original sticker over the hole in the calibration port on the rear of the ventilator was    

 

 

removed, replace with a new ‘calibration void’ sticker.

 

 

 

Attach the required notification to the ventilator which states that the unit has passed its final  

 

 

test.

 

Calibration Gas   

 

 

 

 

 

As specified by model number 

Gas Convert   

 

 

 

 

 

 

Norm 

BAV Software Version  

 

 

 

8.60 

Front Panel Software Version  

 

8.20 

Ventilator Model No: 
Manufacture Date 

(part of serial no.) 

Calibration Date: 

All options on second sheet are at default.

 

  5.26  Printer Output 

Connect the serial printer to the recorder output. 

With no pneumatic connections attached, turn the ventilator ON (adult mode) and check that 
the printer starts operating after a few seconds. Note the output software version on the 
checklist and calibration record and any other details required in the record header. 

 

Summary of Contents for 8500






































































Reviews:

No comments