manualshive.com logo in svg

Blease 8500, Training Manual, Page: 37 / 69

Share
Download
Blease 8500 Training Manual Download Page 37

Title:  Final Test 8500 

Document No: 129TP000 

Sheet 10 of 17 

 

 

 

BLEASE QUALITY DOCUMENT 

BQD 083.V2 

25/5/94   

 

 

 

 

 

 

 

 

 

 

Checked:-________   

 
 

 

Switch the ventilator to paediatric mode and carry out compliance compensation as directed 

 

 

on screen: 

 

 

 

 

Set ventilatory controls to: 

 

 

 

 

 

TV = 0.5L/50ml 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Freq = 10 BPM 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ratio = 1:2.5 

 

 

Note bellows movement. 

 
 

 

Set ventilatory controls to: 

 

 

 

 

 

TV = 2L/200ml 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Freq = 10 BPM 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

Ratio = 1:2.0 

Note bellows movement. 
 

5.17  Paediatric Pressure Limit 

 
 

 

Set ventilatory controls to: 

 

 

 

 

 

TV = 6L/200ml 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Freq = 30 BPM 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ratio = 1:2.0 

Set pressure limit to 20 cm H

2

O and note the delivered peak pressure after several breaths. 

Note the bellows position. 

Disconnect lower patient airway connector. 

Note peak pressure. 

 

 

 

 

 

Switch the ventilator to Adult mode and carry out compliance compensation as directed   

 

 

 

on screen: 

 

 

Summary of Contents for 8500






































































Reviews:

No comments