manualshive.com logo in svg

Blease 8500, Training Manual, Page: 29 / 69

Share
Download
Blease 8500 Training Manual Download Page 29

Title:  Final Test 8500 

Document No: 129TP000 

Sheet 2 of 17 

 

 

 

BLEASE QUALITY DOCUMENT 

BQD 083.V2 

25/5/94   

 

 

 

 

 

 

 

 

 

 

Checked:-________   

 

 
DURING TESTING, ALWAYS BE AWARE OF CORRECT VENTILATOR OPERATION AND 
LISTEN FOR ANY UNEXPECTED OR UNUSUAL NOISES FROM THE MACHINE AND 
ASSOCIATED TUBING, AS THIS MAY INDICATE A POTENTIAL PROBLEM. 
 

ALWAYS COMPLETE COMPLIANCE COMPENSATION AFTER SWITCHING THE 
VENTILATOR OFF AND BACK ON AGAIN.  ALWAYS WAIT FOR COMPLIANCE 
COMPENSATION TO COME BACK ON BEFORE TAKING ANY READINGS. 

4.0   TEST LIMITS SPECIFICATION

 

Sched.            Function set   

 

 

Parameter  

 

 

 

Tolerance   

 

Units 

Ref.   

 

 

or tested   

 

 

 

Measured 

5.3   

 

 

Mains connected   

   Mains Supply   

      

90-265   

      

Vac 

 

 

 

 

 

(500 Vdc)   

 

 

 

Mains insul Res   

 

 50   

          

Mohms 

 

 

 

 

 

 

 

 

 

 

 

(25 A ac)   

 

 

 

Equip cont Res   

    

≤

 0.2   

 

 

     Ohms 

 

 

 

 

 

 

 

 

 

 

 

 

 

Norm leakage   

       

≤

 500  

 

 

 

µ

A 

 

 

 

 

 

 

 

 

 

 

 

 

 

Revs leakage   

      

≤

 500  

 

 

 

µ

A 

 

 

 

 

 

 

 

 

 

 

 

 

 

O/C norm leakage   

≤

 1000   

          

µ

A 

 

 

 

 

 

 

 

 

 

 

 

 

 

O/C revs leakage   

 

≤

 1000   

          

µ

A 

 
5.8   

 

 

Mute ON   

 

 

 

Mute times  

 

 

 

120 ± 2   

 

 

sec 

 
5.9   

 

 

Supply alarm ON  

 

Supply gas pressure   

34.5 - 36.0   

 

psi 

 

 

 

 

 

Supply alarm OFF   

Supply gas pressure   

≤

 36.0   

 

 

psi 

5.10   

 

 

 

 

                

6 BPM/1:1.0    

 

1.0 L delivered   TV  0.93 - 1.07  L 

 

 

               10 BPM/1:2.0      

1.0 L delivered   TV  0.95 – 1.05  L 

 

 

               20 BPM/1:3       

0.6 L delivered   TV  0.55 - 0.65   L   

 

 

      

 

20 BPM/1:2      

0.2 L delivered   TV  0.17 - 0.23  L 

 

 

 

 

 

60BPM/1:1.0      

0.2 L delivered   TV  0.17 - 0.23  L  

 

 

               90BPM/1:2.0      

0.1 L delivered   TV  0.08 - 0.12  L 

 
NOTE:  i.e.  MAX  =  1:5.1 

 

 

 

The bellows deflection is affected by compliance compensation and this should be    

 

 

 

 

considered when judging the results.

 

   
 

 

A fresh gas supply of 0.25 L/m, will add about 10 ml to the breath at 6-10 BPM and can be 

 

 

ignored at higher rates. The above tolerances allow for this. 

 

 

Also included is additional 

±

 10 ml for Calibration Analyser display error. 

 

 

 

 

 

Delivered TV = Total TV / (1 + Vent compl/Pat compl) where ventilator adult compliance   

Summary of Contents for 8500






































































Reviews:

No comments