manualshive.com logo in svg

Blease 8500, Training Manual, Page: 4 / 69

Share
Download
Blease 8500 Training Manual Download Page 4

8500 Ventilator 

Training Manual

 

4 

 

 

 

The Blease 8500 ventilator must only be serviced by Qualified Service Personnel. 

The contents of this manual are not binding.  If any significant difference is found between 
the product and this manual please contact Blease Medical Equipment Limited for further 
information. To ensure correct functioning, the equipment must be serviced at regular in-
tervals. 

Blease Medical Equipment Limited recommends that the machine should be serviced at 
intervals not exceeding three months.  Qualified Service Personnel and genuine spare 
parts should be used for all servicing and repairs.  Blease Medical Equipment Limited will 
not otherwise assume responsibility for the materials used, the work performed or any pos-
sible consequences of the same. 

In communication with Blease Medical Equipment Limited, quote the model and serial 
number of the equipment, with the approximate date of purchase.  If the unit is being re-
turned for repair, indicate the nature of the fault or the work you require to be carried out. 

Contact:  
                                  Blease Medical Equipment Limited 
                                  Beech House 
                                  Chiltern Court   
                                  Asheridge Road   
                                  Chesham   
                                  Buckinghamshire  
                                  HP5 2PX   
                                  England 
                                  Tel:     +44 (0)1494 784422 
                                  Fax:    +44 (0)1494 791497 
                                  www.blease.com 
                                  [email protected] 

 

Summary of Contents for 8500






































































Reviews:

No comments