Blease 8500 Training Manual Download Page 32

Page: 32 / 69

Title: Final Test 8500

Document No: 129TP000

Sheet 5 of 17

BLEASE QUALITY DOCUMENT

BQD 083.V2

25/5/94

Checked:-________

20R

Resistor

20 L

Compliance

12600010

Calibration

Analyser

Fresh gas is set for minimum required
to maintain full bellows <0.5 l/min

Lo pressure
Inlet P+

Anaesthesia Ventilator

Bellows and Absorber

Driving
Gas

Short Hose

Hi Flow

Outlet

Hi Flow

Inlet

Patient

Circuit

Fresh Gas Sensor

Patient

Flow Sensor

5.2 Initial Checks

Fill out the header at the top of the 'Checklist and Calibration Record' (129TC000) for the unit

being tested. This will include the serial number of the Ventilator plus the date of testing, the

gasses used, software version, catalogue number and model.

Factory test does not require cover and lid at the initial stage.

Visually inspect the overall machine for any defects. In particular check:

•

The mains cable is firmly attached to the ventilator and locked in place.

•

The correct mains plug is fitted for the country.

•

The supply gas inlet is for oxygen (unless specified differently), and orientation is such

as to show gas type uppermost. Note USA or UK type fitting.

•

The finger proof exhaust gas outlet is fitted.

•

The supply gas label is the right colour for gas/country. USA oxygen is green, USA air is

yellow, UK oxygen is white and UK air is chequered white/black.

•

Verify the bellows size, adult or paediatric.

5.3 Earth Leakage and Continuity

With the electrical safety tester set to the following test positions (with its test selector knob),

perform the following checks and note all results from the electrical safety tester meter.

Summary of Contents for 8500






































































Search results

Summary of Contents for 8500

Reviews:

Blease 8500, Training Manual, Page: 32 / 69

Search results

Summary of Contents for 8500

Reviews: