manualshive.com logo in svg

BLADDERSCAN BVI 9400, Operation & Maintenance Manual, Page: 71 / 84

Share
Download
BLADDERSCAN BVI 9400 Operation & Maintenance Manual Download Page 71

63

Operations & Maintenance Manual: Troubleshooting

TROUBLESHOOTING PROCEDURES

PROCEdURE 1.  TROUBLESHOOT SCAN POINT CONNECTION

Complete this procedure if the console cannot connect to Scan Point

®

.

1.  Ensure the 

Scan Point

 button 

 was pressed and the console is searching for a connection.

2.  In Scan Point, try connecting again by clicking the 

Find New 

button. Repeat this step up to 3 times. 

If the console does not connect, continue to the next step.

3.  Turn the console off, turn the console on, and then press the 

Scan Point

 button 

. On the PC, in 

Scan Point, click 

Find New

.

If the console does not connect, continue to the next step.

4.  While the instrument is attempting to connect to Scan Point, remove the battery.

5.  Reinsert the battery, allow the instrument to power on, and then press the 

Scan Point

 button 

.

6.  On the PC, click 

Find New

.

If the console does not connect, contact Verathon

®

 Customer Care.

Summary of Contents for BVI 9400





















































































Reviews:

No comments