manualshive.com logo in svg

BLADDERSCAN BVI 9400, Operation & Maintenance Manual, Page: 60 / 84

Share
Download
BLADDERSCAN BVI 9400 Operation & Maintenance Manual Download Page 60

52

CLEANING & MAINTENANCE

This product may only be cleaned and disinfected by using the approved processes provided in 
this manual. Cleaning and disinfection methods listed are recommended by Verathon based on 
compatibility with component materials. 

WARNING

Availability of cleaning and disinfection products varies by country, and Verathon is unable to 
test products in every market. For more information, please contact Verathon Customer Care or 
your local representative. For additional contact information, visit 

verathon.com/support

.

WARNING

Ensure that you follow the manufacturer’s instructions for handling and disposing of the 
cleaning and disinfection solutions provided in this manual.

WARNING

Cleaning is critical to ensuring the component is ready for disinfection. Failure to properly clean the 
device could result in a contaminated instrument after completing the disinfection procedure.

WARNING

Cleaning and disinfecting the instrument is an important part of using and maintaining the device. Prior to 
each use, ensure the instrument has been cleaned and disinfected according to the following procedures.

BEST PRACTICES

Cleaning is the removal of all visible soil or contaminants from the exterior surfaces of the device, and 
disinfection is the process of destroying pathogenic organisms or rendering them inert. When cleaning, 
ensure all foreign matter is removed. This allows the active ingredients of the chosen disinfection method to 
reach all the surfaces of the device.

To significantly reduce the amount of effort needed to clean the system, do not let contaminants dry on any 
system component. Contaminants tend to become securely attached to solid surfaces when dried, making 
removal more difficult.

Change gloves as directed in the procedure or if gloves become soiled.

Summary of Contents for BVI 9400





















































































Reviews:

No comments