manualshive.com logo in svg

BLADDERSCAN BVI 9400, Operation & Maintenance Manual, Page: 12 / 84

Share
Download
BLADDERSCAN BVI 9400 Operation & Maintenance Manual Download Page 12

4

Medical electrical equipment requires special precautions regarding electromagnetic 
compatibility (EMC) and must be installed and operated according to the instructions in this 
manual. For more information, see the 

Electromagnetic Compatibility

 section on page 70. 

To maintain electromagnetic interference (EMI) within certified limits, the BladderScan BVI 9400 
system must be used with the cables, components, and accessories specified or supplied 
by Verathon

®

. For additional information, see the 

System Components & Accessories

 and 

Component Specifications

 sections. The use of accessories and cables other than those specified 

or supplied may result in increased emissions and decreased immunity of the system. 

The BladderScan BVI 9400 system should not be used adjacent to or stacked with other 
equipment. If adjacent or stacked use is necessary, the system should be observed to verify 
normal operation in the configuration in which it will be used. 

This device can radiate radio frequency energy and is very unlikely to cause harmful interference 
with other devices in the vicinity. There is no guarantee that interference will not occur in a 
particular installation. Evidence of interference may include degradation of performance in 
this device or other devices when operated simultaneously. If this occurs, try to correct the 
interference by using the following measures: 

•  Turn devices on and off in the vicinity to determine the source of interference
•  Reorient or relocate this device or other devices
•  Increase the separation between devices
•  Connect the device to an outlet on a circuit different than the other device(s)
•  Eliminate or reduce EMI with technical solutions (such as shielding)
•  Purchase medical devices that comply with IEC 60601‑1‑2 EMC Standards

Be aware that portable and mobile radio frequency communications equipment (cellular phones, 
etc.) may affect medical electrical equipment; take appropriate precautions during operation. 

CAUTION

WARNINGS

Risk of explosion. 

If you use the BladderScan BVI 9400 in the presence of flammable 

anesthetics, the hazard of potential explosion exists.

WARNING

Risk of electric shock or burns. 

Do not use the BladderScan instrument in conjunction with HF 

surgical equipment.

WARNING

Summary of Contents for BVI 9400





















































































Reviews:

No comments