manualshive.com logo in svg

BLADDERSCAN BVI 9400, Operation & Maintenance Manual, Page: 11 / 84

Share
Download
BLADDERSCAN BVI 9400 Operation & Maintenance Manual Download Page 11

3

Operations & Maintenance Manual: Important Information

CAUTIONS & WARNINGS

Warnings

 indicate that injury, death, or other serious adverse reactions may result from use or misuse of 

the device. 

Cautions

 indicate that use or misuse of the device may cause a problem, such as a malfunction, 

failure, or damage to the product. Throughout the manual, pay attention to sections labeled 

Important

, as 

these contain reminders or summaries of the following cautions as they apply to a specific component or 
use situation. Please heed the following warnings and cautions.

PRECAUTIONS

Potential Device Interference.

 Bluetooth

®

 and wireless LAN devices operate within the same 

radio frequency range and may interfere with one another. 

If you are using the BladderScan BVI 9400 Bluetooth link and wireless LAN devices 
simultaneously, you may experience less‑than‑optimal network performance or even lose your 
network connection. If this happens, you may need to move the BladderScan and Scan Point

®

 

host computer to an area away from the 2.4‑GHz wireless LAN devices (40 m [44 yd], or more).

CAUTION

Use of the following cleaning methods or solutions may cause device damage not covered by 
the BladderScan BVI 9400 warranty.

•  Do not immerse the instrument in disinfectant solution.
•  Do not use Cidex Plus

®

 to disinfect the instrument. Cidex Plus will damage the plastic enclosure.

•  Do not subject any part of the instrument to steam sterilization or ethylene oxide sterilization.

CAUTION

When using the BladderScan BVI 9400 with optional Scan Point

®

 software, your computer must 

be minimally certified to IEC 60950‑1 or 61010‑1 standards. This configuration ensures that 
compliance to the IEC 60601‑1 system standard is maintained. Anyone connecting additional 
equipment to the BladderScan BVI 9400 signal input port or signal output port configures 
a medical system, and is therefore responsible for ensuring that the system complies with 
IEC 60601‑1. If you need assistance, contact your biomedical staff, Verathon representative, or 
Verathon Customer Care.

CAUTION

The BladderScan BVI 9400 and related devices may contain mineral oils, batteries, and other 
environmentally hazardous materials. When the instrument or accessories have reached the end 
of their useful service life, see the section 

Device Disposal

 on page 61.

CAUTION

Summary of Contents for BVI 9400





















































































Reviews:

No comments