manualshive.com logo in svg

Blackrock Microsystems Cerebus, Instructions For Use Manual

Share
Download
Blackrock Microsystems Cerebus Instructions For Use Manual Download Page 3

 

Revision 15.00 / LB-0028 

–

 Cerebus Instructions for Use 

3 

The Front End Amplifier power supply red error LED is on. .... 20

 

The analog headstage attached to the Front End Amplifier is 
not receiving power. ............................................................... 20

 

The fiber optic LED indicator is illuminating red. .................... 21

 

The source status LED on Digital Hub is illuminating red. ....... 21

 

The Central application fails to start. ...................................... 22

 

Warranty ..................................................................................... 23

 

Support ........................................................................................ 23

 

Appendix 1................................................................................... 24

 

Warnings ................................................................................ 24

 

Cautions .................................................................................. 24

 

Specifications .......................................................................... 24

 

Symbols of Contraindications, Warnings, Cautions ................ 25

 

Appendix 2................................................................................... 26

 

Electromagnetic Immunity ..................................................... 26

 

 
 
 

 

Summary of Contents for Cerebus




























Reviews:

No comments

Brands by name

Popular brands

Load more brands