background image

The contents of the manual may differ when the purchased lift is modified. For any 
question about the product or this manual, feel free to contact your lift supplier.

Keep this manual in a safe place for future reference. In case of loss, contact your 
lift supplier and request for a new copy immediately.

Thank you for purchasing our 

Bishamon Multi Lift

. Before using the lift, read through

and be familiar with this manual.  Fully understand the precautions, directions, and
other information contained in this manual to ensure correct use.   Failure to do so may
result not only in insufficient performance of the lift but also in falling of the
vehicle, serious injury and death, and damage to properties.

In this manual,  

Danger

,

Warning

Caution

are defined and 

specified as below.  Notice of Warnings are very important for safe operations.  As 

these are very  Important to protect operators from accidents resulting in  

personal injury and death, and damage to property, so make sure to read 

thoroughly and understand fully before operation.

Danger      

Incorrect operation may imminently result in serious                                                                         

injury or  death of the operator.

Warning

Incorrect operation may result in serious injury or  

death of the operator. 

Caution

Incorrect operation may result in injury and damage

to the property. The occurence of the danger is lower 
than "Warning" articles.

Explanation of Terms and Symbols

Summary of Contents for Multi Lift MUS40HU










































Reviews: