Bionet CardioCare 2000 Operation Manual Download Page 34

Page: 34 / 61

34 / 61

Ver. 2.41

CardioCare2000 Operation Manual

Filter Setting

AC power noise, base line drift caused by breathing , EMG signal can be recorded along with

the output ECG signal. To set the AC noise filter, move to

“FLT” menu to call up “AC” menu

and press

key.

key toggles between off, 50hz, 60hz. Off indicates that filter does

not suppress ac interference. As for 50Hz or 60Hz, filter suppresses 50Hz or 60Hz AC power

noise. In case of battery power, ECG signal is clear only with Off setting because AC noise

interference hardly exist. The selection is 50Hz for most of Europe and 60Hz for USA and other

countries. The selected setting is shown on the bottom line of the output form indicated by Cut

off AC.

Base line drift is caused by patient breath. Base line drift filter can be set by pressing

key.

BASE

key switches on or off. On or off indicates base lien filter is applied or not. The

selected setting is shown on the bottom line of the output form indicated by

‘0.1hz-‘ as for filter

on and

‘0hz-‘ as for filter off.

EMG signal is induced from muscle and internal organs of the patient.

For clear ECG signal output, it is necessary to eliminate EMG signal interference.

EMG filter can be set by pressing MUSC

key. MUSC

key switches on or off. On

or off indicates EMG filter is applied or not. The selected setting is shown on the bottom line of

the output form indicated by Cut off EMG.

Low pass filter can be selected to optimize ECG signal after applying above three filters and if

ECG signal is still interfered. To set the low pass filter, move the menu to

“FLT” to call up “LPF”

menu and press

key.

key toggles between off, 40hz, 100hz, 150hz. As for 40Hz,

it indicates filter suppresses higher frequency than 40Hz. The selected setting is shown on the

bottom line of the output form indicated by

‘-250hz-‘ as for off, by’-40hz’ as for 40hz, by’-100hz’

as for 100hz, by

’-150hz’ as for 150hz.

To apply filter could result in ECG distortion. So, filter should be appropriately applied to reduce

the fluctuation without affecting the ECG signal when output signal is badly interfered only.

For your reference, base line file and ac filter should be always active and EMG filter can be

applied appropriately. It is recommended for LPF to set 150Hz during diagnosis.

Summary of Contents for CardioCare 2000






























































Search results

Summary of Contents for CardioCare 2000

Reviews:

Related manuals for CardioCare 2000

Brands by name

Popular brands

Bionet CardioCare 2000, Operation Manual

Search results

Summary of Contents for CardioCare 2000

Reviews:

Related manuals for CardioCare 2000

Brands by name

Popular brands