Big Backyard F24015 Installation And Operating Instructions Manual Download | Manualshive

Page: 35 / 56

background image

35

[email protected]

Step 18: Attach Ground Stakes

A:

Drive 3 (0318) Ground Stakes 10-1/2” into the ground against (1928) Lower Side at (1500) Post and

(0369) Lower Diagonal and against (1914) Cafe Ground at (1500) Post as shown in fig. 18.1. Attach using 2

(S3) #8 x 2-1/2” Wood Screws per ground stake. (fig. 18.1 and 18.2)

MOVE FORT TO FINAL LOCATION. FINAL LOCATION MUST BE LEVEL GROUND

Warning! To prevent tipping and avoid potential injury, stakes must be

driven 10-1/2” into ground. Digging or driving stakes can be dangerous if

you do not check first for underground wiring, cables or gas lines.

Wood Parts

3 x

Ground Stake 1-1/4 x 1-1/2 x 14”

6 x

#8 x 2-1/2” Wood Screw

Hardware

Fig. 18.1

0318

S3

1928

0369

0318

1500

S3

10-1/2” In Ground

1500

1914

Fig. 18.2

0318

«
...
33
34
35
36
37
...
»

Summary of Contents for F24015

























































Reviews:

No comments

Related manuals for F24015

Brand: Acer Pages: 2

Brand: Acer Pages: 4

Brand: Kargo Master Pages: 5

Brand: Kappa Pages: 4

Brand: Nacon Pages: 12

Brand: Eclipse Pages: 6

Brand: Watts Pages: 8

Brand: HALE Pages: 44

Brand: Kargo Master Pages: 5

Brand: Vega Pages: 20

Brand: Vega Pages: 88

Brand: Vega Pages: 28

Brand: Vega Pages: 92

KO PROPO RTF 2002 ESC

Brand: Tamiya Pages: 2

PWR10 AL SILVER

Brand: Navitel Pages: 15

Brand: AirCaddy Pages: 12

Lyra 1350 Twin Wall - Door Cover

Brand: Palram Pages: 16

Nimbie Sidekick NK50Y

Brand: Acronova Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands