Big Backyard F24015 Installation And Operating Instructions Manual Download

Page: 20 / 56

[email protected]

Step 6: Swing Wall Assembly

Part 1

Attach (1928) Lower Side, noticing the

side the bolt hole on the extended end is on,

using 4 (H2) 1/4 x 2” Hex Bolts (with lock

washer, flat washer and t-nut); (1924) SW

Floor (in the bottom holes) and (1925) SW

Top using 2 (H2) 1/4 x 2” Hex Bolts (with lock

washer, flat washer and t-nut) for each board

to 2 (1500) Posts. (fig. 6.1)

Note: Keep all

bolts loose.

On the side indicated in fig. 6.1, attach

(0369) Lower Diagonal to (1928) Lower

Side with 1 (H2) 1/4 x 2” Hex Bolt (with lock

washer, flat washer and t-nut).

Notice overhang

at this side

Wood Parts

Hardware

1 x

SW Top 1 x 4 x 36”

1 x

SW Floor 1 x 6 x 26-7/8”

1 x

Lower Side 1 x 5 x 59-11/16”

2 x

Post 2 x 4 x 83”

1 x

Lower Diagonal 2 x 3 x 37”

1925

9 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

0369

1500

1928

1924

Fig. 6.1

1/4” Flat

Washer

1/4”

T-Nut

1925

1/4” Lock

Washer

1500

1924

1928

1500

0369

Notice bolt hole

on this side.

Notice the

hole locations

of (1924) SW

Floor

Summary of Contents for F24015

























































Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands

Big Backyard F24015, Installation And Operating Instructions Manual

Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands