Big Backyard F24015 Installation And Operating Instructions Manual Download

Page: 22 / 56

[email protected]

1913

Back Floor

1764

Floor Front

1/4 x 4" HB

1/4 x 4.75" HB

No. 12 x 2" Pan

Screw

Wood Parts

Hardware

Step 7: Fort Frame Assembly

1 x

Back Floor 1 x 6 x 38-3/4”

1 x

Floor Front 2 x 3 x 38-1/2”

1913

2 x

1/4 x 4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

1/4 x 4-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

2 x

#12 x 2” Pan Screw (3/16” flat washer)

1764

On the front of the assembly, side without the (0369) Lower Diagonal, attach (1764) Floor Front to both

(1500) Posts, noticing the bolt holes are towards the bottom of the board, with 2 (H6) 1/4 x 4-3/4” Hex Bolts (with

lock washer, flat washer and t-nut). (fig. 7.1 and 7.2)

On the back side of the assembly attach (1913) Back Floor to both (1500) Posts, noticing the middle bolt

hole is oriented towards the bottom, with 2 (H4) 1/4 x 4” Hex Bolts (with lock washer, flat washer and t-nut) in the

bottom holes. (fig. 7.1 and 7.2)

Make sure (1913) Back Floor is level and square to the posts, then attach with 2 (S7) #12 x 2” Pan Screws

(with 3/16” flat washer). (fig. 7.1 and 7.2)

Fig. 7.2

1500

Fig. 7.1

1913

1500

1764

0369

1/4” Flat

Washer

1/4”

T-Nut

1/4” Lock

Washer

3/16” Flat

Washer

1500

1/4” Flat

Washer

1/4” Lock

Washer

Notice the hole

towards bottom

of board

Notice the hole

towards bottom

of board

1913

1764

Summary of Contents for F24015

























































Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands

Big Backyard F24015, Installation And Operating Instructions Manual

Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands