Big Backyard F24015 Installation And Operating Instructions Manual Download

Page: 31 / 56

[email protected]

Step 14: Front Wall Frame Assembly

Attach (1916) Front Divider to (1764) Floor Front with 1 (H6) 1/4 x 4-3/4” Hex Bolt (with lock washer, flat

washer and t-nut).

Keep bolt loose.

(fig 14.1)

Attach (1927) Top Front Back to (1916) Front Divider with 1 (H4) 1/4 x 4” Hex Bolt (with lock washer, flat

washer and t-nut).

Keep bolt loose.

(fig. 14.1)

Make sure (1927) Top Front Back is level then attach to both (1500) Posts with 4 (S7) #12 x 2” Pan Screws

(with 3/16” flat washer). (fig. 14.1)

D: Tighten all bolts from this step.

Fig. 14.1

1500

1/4” Flat

Washer

1/4”

T-Nut

1/4” Lock

Washer

1927

1764

1500

1916

Wood Parts

Hardware

1 x

Top Front Back 1 x 4 x 56-3/4”

1 x

Front Divider 2 x 4 x 59-1/4”

1 x

1/4 x 4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

1 x

1/4 x 4-3/4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

4 x

#12 x 2” Pan Screw (3/16” flat washer)

1927

1916

1/4” Flat

Washer

1/4”

T-Nut

1/4” Lock

Washer

with 3/16”

Flat Washers

with 3/16”

Flat Washers

(Hidden under floor boards)

Summary of Contents for F24015

























































Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands

Big Backyard F24015, Installation And Operating Instructions Manual

Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands