Big Backyard F24015 Installation And Operating Instructions Manual Download

Page: 49 / 56

[email protected]

Glider Rope

and Chain

Glider End

5/16 Flat

Washers

Glider Seat

5/16 x 6” Hex

Bolt

5/16 Flat

Washer-Zinc

5/16 Lock Nut

5/16 Flat

Washer-Zinc

5/16 Lock

Nut

Warning! Bolt must not exceed

1/2 thread past the nut

5/16 Lock

Nuts

Step 31: Glider Assembly

Attach 1 Glider End to the Glider Seat using 1 (Z) 5/16 x 6” Hex Bolt (with 2 flat washers and 1 lock nut).

Repeat for the second Glider End. (fig. 31.1)

Install 2 Glider Rope with Chains into each Glider End using 2 - 5/16” Flat Washers and 1 Lock Nut per rope.

(fig. 31.1)

Other Parts

Hardware

2 x Glider Ends
1 x Glider Seat
1 x Glider Rope and Chain (pkg of 4)

2 x

5/16 x 6” Hex Bolt

(5/16” flat washer x 2, 5/16” lock nut)

8 x 5/16” Flat Washer
4 x 5/16” Lock Nut

Fig. 31.1

Summary of Contents for F24015

























































Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands

Big Backyard F24015, Installation And Operating Instructions Manual

Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands