Big Backyard F24015 Installation And Operating Instructions Manual Download

Page: 33 / 56

[email protected]

1779

Attach (1779) CE Access Board flush to the top and outside edges of each (0349) Rock Rail with 4 (S2) #8 x

1-1/2” Wood Screws. (fig. 16.1 and 16.2)

Below (1779) CE Access Board stagger 3 (1777) CE Rock Board B and 2 (1778) CE Rock Board A, making

sure they are evenly spaced with a minimum 2-1/8” and maximum 2-3/8” gap. The sides are flush to the outside

edges of each (0349) Rock Rail. Attach using 4 (S2) #8 x 1-1/2” Wood Screws per board. (fig. 16.1 and 16.2)

Place the CE Rock Boards as you desire, but watch the hole placement to prevent rocks from forming a

straight line.

Note: Gaps

between boards

2-1/8”, not to

exceed 2-3/8”

Note: The holes

in the rock boards

must orient to the

top of the boards.

Step 16: Rock Wall Assembly

Wood Parts

1 x

CE Access Board 1 x 6 x 17”

3 x

CE Rock Board B 1 x 6 x 17”

2 x

CE Rock Board A 1 x 6 x 17”

24 x

#8 x 1-1/2” Wood Screw

1779

Hardware

1777

1778

Fig. 16.1

1779

0349

Flush

Fig. 16.2

1777

1778

x 4 per board

Summary of Contents for F24015

























































Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands

Big Backyard F24015, Installation And Operating Instructions Manual

Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands