Big Backyard F24015 Installation And Operating Instructions Manual Download

Page: 21 / 56

[email protected]

Step 6: Swing Wall Assembly

Part 2

Place (1861) SW Mount across (1924) SW

Floor and (1925) SW Top and attach using 2

(G4) 5/16 x 4” Hex Bolts (with lock washer, flat

washer and t-nut) as shown in fig. 6.2. Notice

the side hole locations are towards the top of the

board.

Note: Pre-drill all holes using a 1/8” drill bit

before installing the lag screws.
D:

Make sure assembly is square then fasten

(1924) SW Floor to (1500) Posts in the top holes

using 2 (LS1) 1/4 x 1-1/2” Lag Screws (with flat

washer); and (0369) Lower Diagonal to (1500)

Post with 1 (LS3) 1/4 x 3” Lag Screw (with flat

washer). (fig. 6.2)

Tighten all bolts.

Wood Parts

Hardware

1 x

SW Mount 2 x 4 x 38-1/8”

2 x

1/4 x 1-1/2” Lag Screw (1/4” flat washer)

1 x

1/4 x 3” Lag Bolt (1/4” flat washer)

2 x

5/16 x 4” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

1861

LS1

LS3

5/16” Flat

Washer

5/16”

T-Nut

5/16” Lock

Washer

LS1

LS3

LS1

1861

Notice the hole

locations of (1861)

SW Mount

1/4” Flat

Washer

1/4” Flat

Washer

1925

1500

1924

0369

1/4” Flat

Washer

Fig. 6.2

Summary of Contents for F24015

























































Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands

Big Backyard F24015, Installation And Operating Instructions Manual

Search results

Summary of Contents for F24015

Reviews:

Related manuals for F24015

Brands by name

Popular brands