Beko BEKOMAT 16 CO Original Installation And Operation Manual Download Page 9

Page: 9 / 60

2.5 Safety instructions

Safety instructions warn against residual risks when handling the product and accessories.
These safety instructions must be strictly observed in order to prevent accidents, personal injury, damage to property
and impairments during operation.

Structural design of the safety instructions:

SIGNAL WORD

Type and source of danger!

Safety symbol

Possible consequences if the danger is ignored
• Measure to prevent the danger

Signal words:

DANGER

Imminent hazard

Consequences of non-compliance: Death or serious personal injury

WARNING

Imminent hazard

Consequences of non-compliance: Death or serious personal injury are possible

CAUTION

Potential hazard

Consequences of non-compliance: Personal injury or damage to property are possible

NOTE

Additional notes, information, tips

Consequences of non-compliance: Malfunction and device failure during handling and

maintenance are possible. No hazard to people or regarding the safe operation.

Original installation and operation manual

BEKOMAT

16 CO

9 | 60

Summary of Contents for BEKOMAT 16 CO





























































Search results

Summary of Contents for BEKOMAT 16 CO

Reviews:

Related manuals for BEKOMAT 16 CO

Brands by name

Popular brands

Beko BEKOMAT 16 CO, Original Installation And Operation Manual

Search results

Summary of Contents for BEKOMAT 16 CO

Reviews:

Related manuals for BEKOMAT 16 CO

Brands by name

Popular brands