Beko BEKOMAT 16 CO Original Installation And Operation Manual Download Page 22 | Manualshive

Page: 22 / 60

background image

Wrong

Right

Description / explanation

Deflecting surface!

In the case of direct drainage from the compressed

gas line a deflection of the compressed gas flow is

necessary!

Continuous slope!

If a pressure hose is used for inflow, avoid the

formation of a water pocket!

Continuous slope!

When laying pipes for the feed line, avoid the

formation of a water pocket.

Continuous slope!

Lay the condensate inlet line with a continuous slope!

If the installation height is limited, mount the lower

inlet with a separate venting line.

Note the minimum height of installation!

The height of the condensate inlet must be located

lower than the lowest point of the collecting tank (e.g.

vessel).

BEKOMAT

®

16 CO

Original installation and operation manual

22 | 60

«
...
20
21
22
23
24
...
»

Summary of Contents for BEKOMAT 16 CO





























































Reviews:

No comments

Related manuals for BEKOMAT 16 CO

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: E-Z DRILL Pages: 12

Brand: e-survey Pages: 54

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: Xebex Fitness Pages: 15

Brand: qeedo Pages: 2

Brand: Hakko Electronics Pages: 8

Professional HS 8

Brand: Hailo Pages: 5

Brand: Hainbuch Pages: 52

Brand: Halyard Pages: 88

Brand: HALDER Pages: 2

Brand: Hällde Pages: 40

Brand: Hällde Pages: 6

Brand: Hammer Strength Pages: 18

Brand: M-Audio Pages: 25

Brand: Safavieh Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands