manualshive.com logo in svg

Beckman Coulter SX4750A, Instruction For Use, Installation And Assembly

Share
Download
Beckman Coulter SX4750A Instruction For Use, Installation And Assembly Download Page 12

GX-TB-004EE   

1-2

SX4750A Swinging-Bucket Rotor

Description  

Description

This Beckman Coulter rotor has been manufactured in an ISO 9001 or 13485 facility for use with the 

specified Beckman Coulter centrifuges

.

The SX4750A is a four-place swinging bucket rotor. The rotor buckets carry adapters that allow 

centrifugation of a wide range of tube and bottle sizes (from 1.5 mL reaction vials to 750-mL bottles) 

or single- to quad-pack blood bags as well as multiwell plates in carriers. Special adapters are also 
available that allow centrifugation of Corning canted-neck 75-cm

2

 and 25-cm

2

 cell culture flasks. 

The rotor develops centrifugal forces that are suitable for rapidly sedimenting protein precipitates, 

large particles, cells, and cell debris.

The rotor yoke is made of stainless steel. Black-anodized aluminum buckets and carriers can be run 

by placing them over pivot pins on the arms of the yoke; they swing out to horizontal position 
during centrifugation. Transparent covers made of high-impact plastic have been tested

*

 to 

demonstrate containment of microbiological aerosols under normal conditions of the associated 

Beckman Coulter centrifuge when used and maintained as instructed. A captive tie-down device is 

used to secure the rotor to the drive shaft during centrifugation.

The ARIES (Automated Rotor Imbalance Equilibrating System) technology provides imbalance 

compensation for rotors with buckets that are up to 50 grams unbalanced.

The centrifuge identifies the rotor during the run by means of a magnetic sensor system in the 

centrifuge rotor chamber and magnets imbedded in the rotor. The overspeed system ensures that 

the rotor does not exceed its permitted speed.

Refer to the Warranty at the back of this manual for warranty information.

1.

Yoke

2.

Bucket

3.

Bottle

4.

Carrier

5.

Carriage

* Validation of microbiological containment was done at an independent third-party testing facility (Public Health 

England). Improper use or maintenance may affect seal integrity and thus containment.

1

3

5

2

1

4

Summary of Contents for SX4750A















































Reviews:

No comments

Brands by name

Popular brands

Load more brands