Beam Oceana 400 User Manual Download

Page: 6 / 31

Terra400 & Oceana400 - Installation & User Manual

Package Contents

Check that your TR400 or OC400 package
contains all of the following items:

1 x Terra 400 Terminal

1 x ISD700 Directional/Fixed
Antenna (Passive)

1 X Oceana 400 Terminal

1 x ISD700 Maritime Antenna (Active)

AND

1 x 110-240V AC Plug Pack

1 x

10-32V DC Power Cable

1 x USB Cable

User Manual & Quick Start Guide

Falcon software is available for download from:

http://www.beamcommunications.com/
falcon

Optional Accessories

The following optional accessories are available
for your TR400 or OC400 terminal

TR400:

Antenna Cable Kits for Active Antennas
•

ISD936
IsatDock/Terra10m cable kit (Passive)

•

ISD937
IsatDock/Terra 20m cable kit (Passive)

•

ISD939
IsatDock/Terra 30m cable kit (Passive)

•

ISD940
IsatDock/Terra 40m cable kit (Passive)

•

ISD941
IsatDock/Terra 50m cable kit (Passive)

OC400:

Antenna Cable Kits for Passive Antennas
•

ISD932
IsatDock/Oceana 6m cable kit (Active)

•

ISD933
IsatDock/Oceana 13m cable kit (Active)

•

ISD934
IsatDock/Oceana 18m cable kit (Active)

•

ISD935
IsatDock/Oceana 31m cable kit (Active)

•

ISD938
IsatDock/Oceana 40m cable kit (Active)

See your service provider for pricing and
availability of these quality BEAM accessories.

Additional Information

For the latest in supporting software and
documentation for the Terra 400 terminal or the
Oceana 400 terminal please visit:

www.beamcommunications.com/support

Terra 400

Terminal support Inmarsat’s

IsatPhone Link service.

Oceana 400

Terminals support Inmarsat’s

Fleetphone service.

For further information on these services visit:

www.inmarsat.com

Other Resources Available Online

- Advanced Configuration – inbuilt to Falcon
- Quick Start Guide & Manual
- Antenna Installation Guide
- Falcon firmware upgrade if required

Summary of Contents for Oceana 400
































Search results

Summary of Contents for Oceana 400

Reviews:

Related manuals for Oceana 400

Brands by name

Popular brands

Beam Oceana 400, User Manual

Search results

Summary of Contents for Oceana 400

Reviews:

Related manuals for Oceana 400

Brands by name

Popular brands