Bayrol PoolManager Bromine User Manual Download Page 77

Page: 77 / 95

Changing the maintenance program

41.2.3

Configuration

After connecting one or multiple membrane dosing pumps, correct
triggering has to be activated and configured in PoolManager

You'll find all relevant setting in the menu

Service functions

Configuration dosing

Selecting the pump type

Membrane pump

will activate the triggering of

individual dosing strokes via PoolManager

The default setting for pump type is

Standard.

intended for conventional peristaltic pumps.

Menu

Configuration dosage pumps

Pump type
pH / mV (Cl) / Cl

For membrane pumps, select

Max. no. of strokes
pH / mV (Cl) / Cl

Enter the desired maximum number of strokes
[strokes/min] at a dosing output of 100%.
For more information, also review the section

Determining output

Pump rate
pH / mV (Cl) / Cl

Enter the correct maximum dosing output for the
corresponding dosing pump in [l/h]
(for the maximum number of strokes

IMPORTANT NOTICE!

Incorrect configuration of dosing output

If a pump's dosing output is not configured correctly,
then the following problems will arise:

•

The calculation for duration of manual dosing is not
correct.

•

The configuration assistant
parameters calculates erroneous settings.

INFO
Membrane dosage pump for O2 (BayroSoft)

For O2 dosing (BayroSoft), the pump type

Membrane pump

cannot be selected. For BayroSoft

dosing,  however,  a  membrane  pump  can  be  triggered
with  simple  turning  on  and  off,  like  a  peristaltic  pump.
The  output  desired  can  be  configured  directly  on  the
pump.
This  variation  is  sufficient,  as  PoolManager
doses  either  100%  or  not  at  all.  Therefore,  variable
triggering of individual pump stro

41.2.3.1

Determining output

The maximum number of strokes per minutes must be configured such
that the desired maximum output in l/h is yielded at 100% dosing
output.

Output can be determined for certain stroke rates with the data sheet
for the pump being used, such as for 60 strokes/min, 120 strokes/min,
or 180 strokes for min.

For many pumps, stroke length can also be configured using a
controller on the pump. This also makes it possible to adjust the
pump's output to match needs.

Example:

A maximum pump output of 2.0 l/h is planned for a system. The
maximum stroke frequency on the pump is 180 strokes/min.

Using the pump's data sheet, the desired output of 2.0 l/h is yielded
with maximum stroke length (100%) and a stroke frequency of 40%,
i.e. 72 stokes/min.

Therefore, the maximum number of strokes must be set to 72/min in
PoolManager

in this case. Then PoolManager

dosing pulses per minuted at maximum dosing output (100%). This will
lead to the desired maximum dosing output of 2.0 l/h.

User Manual PoolManager

After connecting one or multiple membrane dosing pumps, correct

and configured in PoolManager

menu.

Configuration dosing pumps

will activate the triggering of

This operating mode is

For membrane pumps, select

Membrane pump.

Enter the desired maximum number of strokes
[strokes/min] at a dosing output of 100%.
For more information, also review the section

Enter the correct maximum dosing output for the

dosing pump in [l/h]

(for the maximum number of strokes entered)

Incorrect configuration of dosing output

If a pump's dosing output is not configured correctly,
then the following problems will arise:

The calculation for duration of manual dosing is not

for configuring control

parameters calculates erroneous settings.

Membrane dosage pump for O2 (BayroSoft)

For O2 dosing (BayroSoft), the pump type

cannot be selected. For BayroSoft

dosing,  however,  a  membrane  pump  can  be  triggered
with  simple  turning  on  and  off,  like  a  peristaltic  pump.
The  output  desired  can  be  configured  directly  on  the

This variation is sufficient, as PoolManager

always

doses either 100% or not at all. Therefore, variable
triggering of individual pump strokes is not necessary.

The maximum number of strokes per minutes must be configured such
that the desired maximum output in l/h is yielded at 100% dosing

Output can be determined for certain stroke rates with the data sheet

the pump being used, such as for 60 strokes/min, 120 strokes/min,

For many pumps, stroke length can also be configured using a
controller on the pump. This also makes it possible to adjust the

A maximum pump output of 2.0 l/h is planned for a system. The
maximum stroke frequency on the pump is 180 strokes/min.

Using the pump's data sheet, the desired output of 2.0 l/h is yielded
with maximum stroke length (100%) and a stroke frequency of 40%,

Therefore, the maximum number of strokes must be set to 72/min in

in this case. Then PoolManager

will generate 72