Bay Networks Remote Annex 2000 Hardware Installation Manual Download Page 35

Page: 35 / 136

2-1

Remote Annex 2000 Hardware Installation Guide

Chapter 2 Installing the Remote

Annex 2000

his chapter contains a description of how to install your Remote

Annex 2000 on your Ethernet network. Installing the Remote Annex
2000 consists of:

❑

Connecting a LAN Using Ethernet.

❑

Connecting a Console Terminal.

❑

Connecting Serial Devices.

❑

Powering Up and Testing the

Remote Annex 2000.

❑

Installing the Software and Loading the Operational Image.

❑

Auto-initializing the ROMs.

❑

Self-booting the Remote Annex 2000.

Before you Begin

The Remote Annex 2000’s software and operational image can be
installed on four different devices.

Table 2-1

outlines the different

configurations the Remote Annex 2000 supports.

Table 2-1. Remote Annex 2000 Configuration Options

Device where the Operational
Software and Image is installed

Remote Annex
2000 Must be
Connected to
the Network

Input Device used to
Enter Installation
Parameters

Novell Server

Yes

PC on the network
or Console

UNIX Load Host

Console

VAX VMS Load Host

Yes

Console

Self-boot Unit (contains Flash)

Console

Summary of Contents for Remote Annex 2000









































































































































Search results

Summary of Contents for Remote Annex 2000

Reviews:

Bay Networks Remote Annex 2000, Hardware Installation Manual, Page: 35 / 136

Search results

Summary of Contents for Remote Annex 2000

Reviews: