manualshive.com logo in svg

Bay Networks Remote Annex 2000, Hardware Installation Manual, Page: 131 / 136

Share
Download
Bay Networks Remote Annex 2000 Hardware Installation Manual Download Page 131

C-13

Remote Annex 2000 Hardware Installation Guide

Appendix C    Warranty and Technical Support Information

Can the unit currently boot?

Y

N

Load host hardware platform:
_________________________________________________________

Load host operating system:
_________________________________________________________

Has the unit booted successfully from this load host and
operating system?

Y

N

If booting the unit for the first time, did you first run the ROM Monitor
erase

 command?

Y

N

Which front panel system indicators were on at the time of failure?

_________________________________________________________

Which front panel status indicators were on or flashing at the time
of failure?

_________________________________________________________

_________________________________________________________

Did the unit pass the Ethernet loopback test? Y

N

If problems are port-related, what were the results of the
ports

command?

_________________________________________________________

_________________________________________________________

_________________________________________________________

_________________________________________________________

Additional information:

Summary of Contents for Remote Annex 2000









































































































































Reviews:

No comments